Ford Forums

Hey guys, my 2015 Ford Transit just threw a P246E code. It says the exhaust gas temperature sensor is stuck, but I’m not exactly sure what to do with that information. I’ve been noticing a bit of a rough idle lately and lower power when going uphill. Could this be related? Anyone know how to fix this without dropping big money at the shop?

Hey everyone, if you’ve stumbled upon this post, chances are you’ve been dealing with that pesky P0430 code on your Ford F-150. I know how frustrating it can be because this code often points to a catalytic converter issue, which can be a costly and time-consuming repair if you’re not prepared. But don’t panic just yet! Let’s break this down and look at what’s really going on, what could be causing the issue, and how you can troubleshoot it yourself before heading to the shop.

The P0430 code indicates that the catalytic converter on Bank 2 (the side of the engine opposite Bank 1) isn’t functioning as efficiently as it should be. Your vehicle’s onboard computer (ECU) monitors the performance of the catalytic converter through the oxygen (O2) sensors located before and after the converter. When the converter’s efficiency drops below a certain threshold, the ECU triggers this code to let you know something's wrong.

Common Symptoms of a P0430 Code

Check Engine Light: This is the obvious one. The P0430 code will trigger your check engine light, which will stay on until the issue is resolved.
Poor Fuel Economy: You might notice your fuel economy taking a hit. A failing catalytic converter can affect the air/fuel mixture, causing the engine to run less efficiently.
Reduced Engine Performance: Your engine might not feel as responsive as it used to, especially when accelerating.
Sulfur Smell: Sometimes, a bad catalytic converter can emit a strong, rotten egg-like smell.

Possible Causes of the P0430 Code

Faulty O2 Sensors

The first thing you’ll want to check are the O2 sensors on Bank 2. There are two sensors: one before the catalytic converter (upstream) and one after it (downstream). These sensors measure the amount of oxygen in the exhaust gases and report this information to the ECU. If the downstream O2 sensor detects that the converter isn’t reducing emissions efficiently, it could trigger the P0430 code.

Use a scan tool with live data capabilities to check the voltage readings from both sensors.
The upstream sensor should fluctuate between 0.1 and 0.9 volts, while the downstream sensor should remain more stable. If the downstream sensor fluctuates as much as the upstream sensor, it might mean the catalytic converter isn’t working properly.

If the O2 sensor is faulty, replace it. Replacing an O2 sensor is relatively inexpensive compared to a catalytic converter, so it’s worth trying this first.

Exhaust Leaks

Even a small leak in your exhaust system can cause the P0430 code. If the leak is between the engine and the catalytic converter, it could throw off the readings from the O2 sensors, leading to incorrect data being sent to the ECU. This can cause the ECU to mistakenly think the catalytic converter isn’t working efficiently.

Troubleshooting Exhaust Leaks:

Visual Inspection: Start by inspecting the exhaust system for any visible damage or holes. Look closely at the connections and gaskets around the catalytic converter.
Listen for Leaks: When the engine is cold, start it up and listen for any hissing or popping sounds around the exhaust system.
Smoke Test: If you have access to a smoke machine, you can use it to find leaks in the exhaust system.
Solution: If you find a leak, repair it. Sometimes, simply replacing a gasket or sealing a small hole can resolve the issue and clear the P0430 code.

Catalytic Converter Failure

Unfortunately, the most common cause of the P0430 code is a failing catalytic converter. Over time, the catalyst material inside the converter can become clogged or contaminated, reducing its ability to break down harmful emissions. If the converter is clogged, you may notice a loss of power, especially when accelerating.

Signs Your Catalytic Converter Is Failing:

Rattling Noise: If you hear a rattling sound coming from the catalytic converter, the internal components may be damaged or broken apart.
Poor Engine Performance: If the converter is clogged, you may notice a lack of power, especially during acceleration.
Excessive Heat: A clogged catalytic converter can cause the exhaust system to overheat. You might notice that the area around the converter feels excessively hot after driving.

If your catalytic converter is failing, it will need to be replaced. Unfortunately, this is not a cheap fix. OEM catalytic converters can cost upwards of $1,000, while aftermarket options may be available for less. Keep in mind that aftermarket converters might not last as long or be as efficient, especially if you live in an area with strict emissions regulations.

Before you rush to replace the catalytic converter, follow these steps to diagnose the issue:


As mentioned earlier, even a small exhaust leak can cause the P0430 code. Use a smoke machine or perform a visual inspection to ensure the exhaust system is sealed properly.

Use a scan tool to read the live data from the O2 sensors. If the downstream sensor’s readings are fluctuating as much as the upstream sensor, replace the downstream sensor first. It’s cheaper and easier than replacing the catalytic converter.

If the O2 sensors are functioning properly and there are no leaks in the exhaust system, the next step is to test the catalytic converter. You can use an infrared thermometer to measure the temperature at the front and rear of the converter. The temperature at the rear should be higher than at the front if the converter is working correctly. If the temperature difference is minimal, it could mean the converter is clogged or failing.

Sometimes, carbon buildup in the catalytic converter can reduce its efficiency. Before replacing the converter, you might try using a fuel additive designed to clean the exhaust system. While this won’t fix a damaged converter, it might help restore some of its efficiency if carbon buildup is the issue.

Once you’ve completed these steps, clear the P0430 code using your OBD-II scanner and take your F-150 for a drive. If the code doesn’t come back, you’ve likely resolved the issue. If it does return, it’s probably time to replace the catalytic converter.

Hey folks, I noticed a few of you have been asking about the KWP2000 code. This one’s a little different because KWP2000 isn’t exactly an error code like P-codes; it’s a communication protocol used by your car’s ECU to send data to diagnostic tools. So, if you’re seeing this, it’s likely because of a connection issue during a scan.

Here’s what you can do:

1. Check your diagnostic tool - Sometimes, cheaper scan tools won’t work properly with the KWP2000 protocol, especially on older Fords.
   
2. Look for loose connections - Double-check the OBD2 connector and make sure there’s nothing blocking the connection.
   
3. Reset the ECU - Sometimes, just resetting the ECU can clear out minor communication issues.
   
4. Update your software - If your scan tool has an update option, try updating it to ensure it’s compatible.
   

Hey all, I’m thinking about getting a small trailer for camping trips, but I’m not sure if my Ford Edge can handle it. Does anyone know the towing capacity, especially for the AWD models? I don’t wanna overdo it and mess up the engine. Thanks!

I’m getting ready for a road trip soon, and I’ll be loading up my 2019 Ford Edge Titanium AWD with quite a bit of gear—probably camping stuff, coolers, the whole works. I know the cargo space is decent, but I’m trying to figure out the exact capacity with the rear seats folded down. From what I’ve read, it should be around 73.4 cubic feet, which sounds good, but has anyone here actually loaded theirs up to the max for a long trip? 

I’m curious to hear how well the space works for bigger items or if there are any tips for organizing things. Also, if you’ve done a big road trip with your Edge, how did it handle being fully packed? Would love to hear your thoughts and any advice on maximizing cargo space for longer trips.

Not saying I’m gonna sell it, but anyone know what a Ford Edge catalytic converter might be worth? I’ve heard scrap prices have been going up lately. Just curious!

If you’re in the market for a used Ford Edge, I’d say your best bet would be the 2015-2019 models. These years seem to be the sweet spot—fewer reported issues, and they come with a lot of modern features without the sticker shock of a brand-new model. The 2.0L and 2.7L EcoBoost engines in these years have proven to be pretty reliable, offering a good balance of power and fuel efficiency. 

Plus, you get advanced safety tech and infotainment systems, which makes them feel more up-to-date. However, I’d always advise checking the vehicle’s service history carefully. Look out for any recalls, especially on the 2015 model, which had a few early issues with things like door latches and some software glitches. If you can find one with low mileage and a clean record, you’re golden. Happy hunting, and don’t hesitate to ask the community if you’re torn between different years—we’ve got plenty of Edge owners here who’ve been through it all!

So, yesterday I was driving my 2016 Ford Edge with the 3.5L V6 engine, and out of nowhere, the ABS light popped on. The strange thing is, the car seems to be braking just fine—no weird noises, no loss of braking power, but that light is still there, staring at me. I know the ABS system is supposed to help prevent skidding, especially during hard braking, so now I’m worried it might not be working if I really need it. 

Could it be something as simple as a bad wheel speed sensor, or am I looking at a bigger issue like a malfunctioning ABS module? Has anyone else dealt with this before? I’d prefer not to rush to the mechanic if it’s something I can troubleshoot at home first. Any tips or advice would be awesome. Should I be freaking out, or is this a common issue with the Edge?

I’m planning to change the spark plugs on my 2018 Ford Edge with the 2.0L EcoBoost engine, but I’m having trouble finding the exact spark plug gap size. I’ve searched the manual and checked a few forums, but I’m still not sure. Some places say it should be around 0.028 to 0.031 inches, but I want to be sure before I start. I’d rather avoid the nightmare of installing the wrong gap and having to pull everything out again! Does anyone have the correct specs or advice on this? Maybe someone with the same engine has done this before? Any help would be really appreciated!

So, I’ve been hearing some rumors about CVT issues with the Ford Edge. Mine’s been running fine so far, but I’m starting to get a bit paranoid. What should I be looking out for? Any early signs of trouble that I should know about?